Bosch Factory Service ManualFault Code: E22

Bosch Dishwasher Error Code E22: Sump Filter Occlusion / Water Circulation Restriction

The electronic control module detects residual water in the tub sump at the conclusion of a wash phase or excessive hydraulic restriction caused by a clogged micro-filter, unlatched pump cover, or sluggish drainage.

OEM Brand: BoschAppliance: dishwasherVerified OEM Diagnostics
Bosch dishwasher diagnostic bench testing and technical inspection for error code E22
Bosch DISHWASHER Diagnostic BenchCODE: E22
Target Appliance

dishwasher

OEM Certified Technical Diagnostic Tree

Diagnostic Tool Required

Digital Multimeter

Measure Ohms resistance, continuity & line voltage.

Triage Complexity

Advanced Diagnostic

5 Sequential manufacturer inspection branches.

Sequential Factory Diagnostic Tree

Perform each diagnostic step in order. Disconnect electrical power and turn off utility shutoffs before inspecting wiring or internal mechanical assemblies.

Digital multimeter measuring ohms resistance and terminal pin continuity on appliance electronic control board
Bench Testing Protocol

Multimeter Resistance & Continuity Verification

Before replacing any electronic control board or mechanical sensor, disconnect power and measure terminal resistance using a calibrated digital multimeter. Verify continuity (0 Ω) across safety switches and compare sensor resistance against OEM specs in the diagnostic steps below.

Step 1: Physical & Electrical InspectionMultimeter & Visual
Action: Remove the lower dish rack, grasp the cylindrical micro-filter handle, rotate 90 degrees counter-clockwise, and lift both the coarse screen and micro-mesh cylinder out of the stainless sump.
Bench Test: Hold the cylindrical stainless micro-mesh screen under a bright light source and run warm tap water through the inside of the cylinder.
Expected Standard: Water flows through micro-pores effortlessly without pooling or dripping; zero grease haze, gelatinous detergent buildup, or calcium scale film.
If Failed / Out of Spec:

Scrub filter with a soft nylon brush, hot water, and liquid grease-cutting detergent (or soak in 50/50 white vinegar solution). If screen is torn or pores remain clogged, replace Sump Micro-Filter Assembly (00645038).

If Passed:

Micro-filter mesh is pristine and translucent. Proceed to Step 2.

Step 2: Physical & Electrical InspectionMultimeter & Visual
Action: Bail residual standing water from the sump basin using a sponge, then inspect the white plastic drain pump impeller cover cap situated on the left side of the sump basin.
Bench Test: Verify that the cover cap is firmly clicked down into place. (Bosch dishwashers rely on this cover cap to create hydraulic suction around the impeller; if loose or missing, water cavitates and code E22/E24 triggers).
Expected Standard: Cover cap is tightly seated under the retention tab with an audible, firm click when pushed downward.
If Failed / Out of Spec:

Reseat white cover cap under the rear retention hook and press down until it audibly snaps locked. If locking tab is broken, replace Drain Pump Impeller Access Cover (00611322).

If Passed:

Cover is locked correctly. Proceed to Step 3.

Step 3: Physical & Electrical InspectionMultimeter & Visual
Action: Using a Torx T20 screwdriver or plastic prying tool, unlatch the white pump cover and remove it. Inspect the exposed black impeller blades inside the pump cavity.
Bench Test: Carefully rotate the pump impeller blades using a gloved finger or wooden stick. Feel for rotational movement.
Expected Standard: Impeller rotates with distinct magnetic resistance in 90-degree steps (notched, springy feel) with zero binding, scraping, or mechanical obstruction.
If Failed / Out of Spec:

Foreign debris discovered (broken wine glass sliver, lemon seed, toothpick, or hair wrapped around shaft). Extract with needle-nose pliers and retest rotation.

If Passed:

Impeller spins smoothly through magnetic detents. Proceed to Step 4.

Step 4: Physical & Electrical InspectionMultimeter & Visual
Action: Locate and remove the black or translucent rubber non-return check valve flapper situated immediately behind the drain pump chamber inside the sump.
Bench Test: Inspect the rubber flapper for physical tears, waviness, mineral scale crust, or debris trapped under the seating lip.
Expected Standard: Flexible, flat rubber flapper that seals airtight against the plastic seat to prevent backflow into the tub.
If Failed / Out of Spec:

Clean flapper and valve seat with isopropyl alcohol. If rubber is deformed or curled, replace Non-Return Check Valve (00165262).

If Passed:

Check valve operates properly. Proceed to Step 5.

Step 5: Physical & Electrical InspectionMultimeter & Visual
Action: Inspect the under-sink corrugated drain hose installation and connection to the garbage disposal or sink branch tailpiece.
Bench Test: Ensure drain hose is looped up to the underside of the countertop (minimum 32 inches high) before descending into the sink drain inlet, and verify disposal inlet plug has been punched out completely.
Expected Standard: Proper high loop maintained; zero sag or kink in hose; 100% unobstructed internal passage through disposal connection barb.
If Failed / Out of Spec:

Clear sink tailpiece blockage or reinstall hose into high-loop bracket (00668108).

If Passed:

Drain path is verified clear; if E22 persists after resetting power for 5 minutes, replace BLDC Synchronous Drain Pump (00631200) or Turbidity/Pressure Sensor (00624323).

Verified OEM Replacement Parts

Cross-referenced factory part numbers for Bosch dishwasher error code E22. Always replace defective components with authentic OEM parts to maintain UL safety certification.

Component NameOEM Part NumberManufacturerStatus
Sump Micro-Filter Screen Assembly00645038BoschDirect Fit OEM
Drain Pump Impeller Access Cover Cap00611322BoschDirect Fit OEM
Non-Return Check Valve Flapper00165262BoschDirect Fit OEM
BLDC Synchronous Drain Pump Motor00631200BoschDirect Fit OEM
Sump Turbidity & Pressure Sensor00624323BoschDirect Fit OEM

Estimated Repair Cost Ranges: Bosch E22

Repair costs for Bosch dishwashers displaying error code E22 vary based on component damage, accessibility, and whether you self-install or dispatch a local factory-trained technician.

DIY Replacement Part

$140 – $340

Direct OEM replacement part cost (excluding tools, shipping, or diagnostic meter equipment).

Pro Diagnostic Fee

$89 – $149

Standard in-home diagnostic evaluation fee by an independent technician (typically applied toward repair).

Total Pro Repair Range

$320 – $590

Typical total job cost including in-home diagnostic, authentic OEM parts, and professional labor (60–120 mins).

Pricing & Diagnostic Disclosure:

The pricing figures provided above represent broad industry averages based on nationwide market surveys and component replacement requirements. Pricing depends on multiple factors including the specific appliance brand, age, mechanical condition, diagnostic complexity, accessibility, and local labor rates. All independent repair contractors set their own independent rates and fee structures. An in-home diagnostic evaluation by an authorized technician is required to provide an exact written quote prior to any repair work.

Related Symptom Triage Guides for Bosch dishwashers

If your appliance displays code E22 alongside physical operational symptoms, consult our dedicated failure triage flowcharts:

Symptom Triage

Why Is My Dishwasher Leaking Water onto the Floor?

View Triage Flowchart →
Symptom Triage

Why Is My Dishwasher Making a Loud Grinding Noise? Diagnostic Guide

View Triage Flowchart →
Symptom Triage

Why Is My Dishwasher Not Cleaning Dishes Properly?

View Triage Flowchart →
Symptom Triage

Why Is My Dishwasher Not Dissolving the Detergent Tablet? Causes & Fixes

View Triage Flowchart →
Engineering Service Hub

Looking for Full Dishwasher Repair Procedures?

Explore comprehensive diagnostic mechanics, component resistance curves, and EPA guidelines for Bosch units.

Dishwasher Repair Specs →
Local In-Home Diagnostic Dispatch

Tired of Troubleshooting Code E22? Get a Local Bosch Technician.

If multimeter bench tests confirm component failure or you prefer a professional to safely service your high-voltage Bosch dishwasher, connect with an independent certified specialist in Colorado, Kansas, or New Mexico today.

(945) 206-7476 Urgent: (855) 796-2411Mon-Sun 7am–9pm • Fast Local Dispatch
Local In-Home Service DispatchSame-Day Available

Need In-Home Diagnostic Dispatch for Code E22?

If multimeter testing confirms an internal short, failed heating element, locked motor, or burnt control board on your Bosch dishwasher, connect with an independent certified technician in your city.

dishwasher repair in Olathe, KS
Olathe, KS Dispatch Hub
→
dishwasher repair in Overland Park, KS
Overland Park, KS Dispatch Hub
→
dishwasher repair in Wichita, KS
Wichita, KS Dispatch Hub
→
dishwasher repair in Lawrence, KS
Lawrence, KS Dispatch Hub
→
dishwasher repair in Topeka, KS
Topeka, KS Dispatch Hub
→
dishwasher repair in Kansas City, KS
Kansas City, KS Dispatch Hub
→
dishwasher repair in Denver, CO
Denver, CO Dispatch Hub
→
dishwasher repair in Colorado Springs, CO
Colorado Springs, CO Dispatch Hub
→
dishwasher repair in Aurora, CO
Aurora, CO Dispatch Hub
→
dishwasher repair in Fort Collins, CO
Fort Collins, CO Dispatch Hub
→
dishwasher repair in Lakewood, CO
Lakewood, CO Dispatch Hub
→
dishwasher repair in Boulder, CO
Boulder, CO Dispatch Hub
→
dishwasher repair in Albuquerque, NM
Albuquerque, NM Dispatch Hub
→
dishwasher repair in Las Cruces, NM
Las Cruces, NM Dispatch Hub
→
dishwasher repair in Rio Rancho, NM
Rio Rancho, NM Dispatch Hub
→
Serving over 120+ cities across Colorado, Kansas, and New Mexico. View all municipal service areas →
Dispatch: (945) 206-7476 Urgent Scenario: (855) 796-2411

Frequently Asked Questions: Bosch E22

What causes Bosch dishwasher error code E22?

The electronic control module detects residual water in the tub sump at the conclusion of a wash phase or excessive hydraulic restriction caused by a clogged micro-filter, unlatched pump cover, or sluggish drainage.

Can I reset the E22 code by unplugging the dishwasher?

While disconnecting power for 5 minutes may temporarily clear the display control memory, the E22 code will reoccur once the microcontroller detects the mechanical or electrical fault again.

What OEM replacement parts are required for Bosch E22?

Common OEM replacement components include: Sump Micro-Filter Screen Assembly (OEM #00645038), Drain Pump Impeller Access Cover Cap (OEM #00611322), Non-Return Check Valve Flapper (OEM #00165262), BLDC Synchronous Drain Pump Motor (OEM #00631200), Sump Turbidity & Pressure Sensor (OEM #00624323).

How much does it cost to fix Bosch dishwasher error code E22?

Professional repair for Bosch dishwasher error code E22 typically averages $320 – $590 in total (including an estimated diagnostic fee of $89 – $149 plus labor and authentic OEM components). Sourcing authentic replacement parts yourself costs approximately $140 – $340. Final prices depend on model specifics, local labor rates, and physical technician inspection.

Dispatch: (945) 206-7476 Urgent: (855) 796-2411