Factory Service Manual Library

Appliance Error Code Diagnostic Directory

Browse verified technical troubleshooting guides for 90 manufacturer fault codes across refrigerators, dishwashers, washing machines, dryers, and ranges. Each guide provides sequential multimeter tests, part numbers, and failure triage.

Diagnostic Manuals by Appliance Category

Dishwashers diagnostic testing and repair procedures20 Codes

Dishwashers

Drain pumps, flood float switches, inlet valves & heat pumps

Washing Machines diagnostic testing and repair procedures21 Codes

Washing Machines

Drive motors, hall sensors, door locks & pressure switches

Dryers diagnostic testing and repair procedures16 Codes

Dryers

Heating elements, thermal fuses, cycling thermostats & sensors

Refrigerators diagnostic testing and repair procedures16 Codes

Refrigerators

Evaporator fans, defrost thermistors, sensors & inverter boards

Ranges & Ovens diagnostic testing and repair procedures0 Codes

Ranges & Ovens

Bake elements, broil igniters, RTD temperature sensors & relays

Filter by Brand:
BoschFrigidaireGELGSamsungWhirlpool

Bosch Fault Codes

25 Documented Codes
Code E09dishwasher

Bosch E09

The integrated flow-through heating element inside the main wash circulation heat pump has suffered an open circuit or burned internal resistive trace.

View Diagnostic Tree β†’
Code E14dishwasher

Bosch E14

The reed switch sensor on the left-side water matrix impellor flow meter is not sending pulses to the control board despite water entering the tub.

View Diagnostic Tree β†’
Code E15dishwasher

Bosch E15

The safety styrofoam float switch located in the bottom plastic base trough has detected accumulated water, activating continuous drain pump operation and halting incoming fill.

View Diagnostic Tree β†’
Code E20dishwasher

Bosch E20

The main wash circulation motor windings exhibit abnormal resistance or an open circuit, preventing wash water pressurization.

View Diagnostic Tree β†’
Code E22dishwasher

Bosch E22

The electronic control module detects residual water in the tub sump at the conclusion of a wash phase or excessive hydraulic restriction caused by a clogged micro-filter, unlatched pump cover, or sluggish drainage.

View Diagnostic Tree β†’
Code E24dishwasher

Bosch E24

The main power module senses abnormal current draw or incomplete water evacuation from the BLDC synchronous drain pump during the initial 1-minute pre-drain sequence, usually caused by a loose impeller cap, blocked non-return valve, or pinched drain line.

View Diagnostic Tree β†’
Code E25dishwasher

Bosch E25

The drain pump motor cannot reach target rotational velocity or the pump cover locking clip is dislodged, causing fluid cavitation.

View Diagnostic Tree β†’
Code E01dryer

Bosch E01

Internal thermal sensors detect excessive temperature rise across the blower housing caused by an obstructed lint screen or clogged exterior exhaust duct.

View Diagnostic Tree β†’
Code E06dryer

Bosch E06

The electronic control module detects no temperature increase during the drying cycle, or the safety thermal limiter fuse has opened.

View Diagnostic Tree β†’
Code E08dryer

Bosch E08

On ventless heat-pump and condensation dryers, the water reservoir float switch detects excessive liquid that the condensate pump failed to evacuate.

View Diagnostic Tree β†’
Code E12dryer

Bosch E12

The control module detects restricted airflow across the condenser unit or exhaust duct, causing excessive internal temperatures.

View Diagnostic Tree β†’
Code Er1oven range

Bosch Er1

The main electronic oven control module senses an open circuit or infinite resistance across the oven cavity PT1000 / NTC temperature probe.

View Diagnostic Tree β†’
Code Er2oven range

Bosch Er2

The electronic clock timer control detects a continuously closed or shorted touch key for greater than 60 consecutive seconds.

View Diagnostic Tree β†’
Code Er3oven range

Bosch Er3

The safety high-limit thermal cutoff switch has opened or the RTD oven temperature sensor detects cavity temperatures exceeding 650Β°F during normal baking.

View Diagnostic Tree β†’
Code Er6oven range

Bosch Er6

The electronic control module detects that the motorized door latch switch did not change state within the programmed timeout period during lock or unlock sequence.

View Diagnostic Tree β†’
Code E01refrigerator

Bosch E01

The electronic control module detects an open circuit or shorted reading from the fresh food refrigerator compartment temperature sensor (NTC).

View Diagnostic Tree β†’
Code E02refrigerator

Bosch E02

The NTC thermistor sensor clipped to the freezer evaporator coil is reporting an open circuit, short circuit, or erratic reading outside normal range.

View Diagnostic Tree β†’
Code E03refrigerator

Bosch E03

The electronic control module detects an open circuit, short, or invalid resistance from the evaporator defrost NTC temperature sensor.

View Diagnostic Tree β†’
Code E10refrigerator

Bosch E10

The door-mounted user interface display panel has lost serial communication with the master inverter power control module in the machine compartment.

View Diagnostic Tree β†’
Code E17washer

Bosch E17

The front-load washing machine did not reach the target water level in the tub within the programmed 6-minute fill timeout window.

View Diagnostic Tree β†’
Code E18washer

Bosch E18

The main electronic control module senses that the water level did not drop to empty within 9 minutes of drain cycle start, indicating pump blockage or failure.

View Diagnostic Tree β†’
Code E20washer

Bosch E20

The wash control board detects an unexpected temperature sensor reading or zero temperature rise during an active wash heating cycle.

View Diagnostic Tree β†’
Code E23washer

Bosch E23

The safety styrofoam float switch located in the bottom metal base pan is elevated by collected leak water, triggering AquaStop shutoff.

View Diagnostic Tree β†’
Code E25washer

Bosch E25

The emergency float switch in the bottom plastic base pan of the washing machine has detected liquid, locking the water valves and activating drain.

View Diagnostic Tree β†’
Code E29washer

Bosch E29

The machine detected an unexpected drop in fill pressure or flow rate during mid-cycle wash or rinse fill operations.

View Diagnostic Tree β†’

Frigidaire Fault Codes

25 Documented Codes
Code i10dishwasher

Frigidaire i10

The electronic pressure sensor detects that the water level in the sump basin failed to reach minimum operating threshold within the allotted fill period.

View Diagnostic Tree β†’
Code i20dishwasher

Frigidaire i20

The electronic control board senses an open pressure switch circuit after draining, indicating water did not evacuate within allowable drain cycle time.

View Diagnostic Tree β†’
Code i30dishwasher

Frigidaire i30

The safety flood protection float switch in the bottom plastic drip tray detected standing water, halting cycle operation and running drain pump continuously.

View Diagnostic Tree β†’
Code i40dishwasher

Frigidaire i40

The main control board detects an analog voltage signal from the pressure transducer that is out of calibration range or completely shorted.

View Diagnostic Tree β†’
Code i50dishwasher

Frigidaire i50

The main control board detects wash pump motor over-current or a shorted motor drive triac, stopping cycle execution to prevent board burnout.

View Diagnostic Tree β†’
Code E4Adryer

Frigidaire E4A

The electronic control board detects that the maximum programmed dry cycle duration (typically 90–120 minutes) was exceeded without clothes drying properly.

View Diagnostic Tree β†’
Code E5Bdryer

Frigidaire E5B

The electronic control board detects that the exhaust thermistor temperature does not rise after the heating element or burner is commanded on.

View Diagnostic Tree β†’
Code E64dryer

Frigidaire E64

The electronic control board detects zero current draw across the electric heating element circuit during a designated heat cycle.

View Diagnostic Tree β†’
Code E68dryer

Frigidaire E68

The electronic control board detects that one of the touch keys on the membrane interface has been shorted or pressed continuously for > 30 seconds.

View Diagnostic Tree β†’
Code F10oven range

Frigidaire F10

The electronic oven control (EOC) board senses that the oven cavity temperature is rising uncontrolled or has exceeded safe threshold while idle or baking.

View Diagnostic Tree β†’
Code F11oven range

Frigidaire F11

The electronic oven control (EOC) board senses a shorted or stuck key contact on the touch membrane matrix for greater than 32 seconds.

View Diagnostic Tree β†’
Code F30oven range

Frigidaire F30

The electronic oven control (EOC) board detects an open circuit or infinite resistance across the oven cavity temperature sensor probe.

View Diagnostic Tree β†’
Code F31oven range

Frigidaire F31

The electronic oven control board detects resistance below 900 ohms across the oven RTD temperature sensor probe, indicating a shorted probe or wiring.

View Diagnostic Tree β†’
Code F90oven range

Frigidaire F90

The motorized door latch assembly failed to reach the target locked or unlocked microswitch position within the programmed 60-second limit.

View Diagnostic Tree β†’
Code dFrefrigerator

Frigidaire dF

The electronic defrost control detects that the evaporator defrost heater failed to raise the defrost bimetal thermostat temperature within maximum allowed time.

View Diagnostic Tree β†’
Code SY CErefrigerator

Frigidaire SY CE

The front door dispenser touch display panel is not receiving valid digital communication packets from the main power board in the rear cabinet.

View Diagnostic Tree β†’
Code SY CFrefrigerator

Frigidaire SY CF

The main electronic power board (located beneath the cabinet or in compressor bay) loses serial communication with the user interface display board in the door.

View Diagnostic Tree β†’
Code SY EFrefrigerator

Frigidaire SY EF

The main electronic control board detects no current draw or tachometer feedback from the freezer evaporator fan motor circuit.

View Diagnostic Tree β†’
Code E11washer

Frigidaire E11

The main electronic control board detects that the wash tub did not reach the target water level within 8 minutes of water inlet valve opening.

View Diagnostic Tree β†’
Code E21washer

Frigidaire E21

The main electronic control board detects that water did not drain from the wash tub within the allowable 4.5-minute drain cycle timeout.

View Diagnostic Tree β†’
Code E41washer

Frigidaire E41

The main control board senses that the front door switch contacts are open when a wash cycle is commanded to start.

View Diagnostic Tree β†’
Code E43washer

Frigidaire E43

The main control board detects a shorted or failed PTC heating element inside the door lock assembly or a burned board lock triac.

View Diagnostic Tree β†’
Code E47washer

Frigidaire E47

The main control board attempts to energize the door lock mechanism but detects an open circuit in the PTC lock solenoid loop.

View Diagnostic Tree β†’
Code E52washer

Frigidaire E52

The motor control board (MCB) energizes the drive motor but receives zero rotational speed feedback pulses from the motor tachometer generator coil.

View Diagnostic Tree β†’
Code E59washer

Frigidaire E59

The main electronic control board (in console) cannot establish or maintain serial data communication with the motor control inverter board (in base).

View Diagnostic Tree β†’

GE Fault Codes

10 Documented Codes
Code FTDdishwasher

GE FTD

The electronic control module detects that water remains in the wash tub sump after the drain pump runs for the maximum drain duration.

View Diagnostic Tree β†’
Code H2Odishwasher

GE H2O

The electronic control module senses low or zero water entering the dishwasher tub during fill sequence, detected by the flood switch and turbidity sensor timeout.

View Diagnostic Tree β†’
Code 001dryer

GE 001

The main electronic control board senses an open circuit in the inlet temperature thermistor circuit (located near the heating element housing).

View Diagnostic Tree β†’
Code 004dryer

GE 004

The main electronic control board commanded the drive motor to run but did not detect motor centrifugal switch closure or rotational feedback within 5 seconds.

View Diagnostic Tree β†’
Code F2oven range

GE F2

The electronic oven control (EOC) board senses that the oven cavity temperature exceeded 590Β°F during normal bake or 990Β°F during self-clean cycle.

View Diagnostic Tree β†’
Code F3oven range

GE F3

The electronic oven control (EOC) detects an open circuit or high resistance (>2,500 ohms) in the RTD temperature probe circuit during bake or broil cycle.

View Diagnostic Tree β†’
Code ERR 01refrigerator

GE ERR 01

The main electronic control board does not detect rotational tachometer speed feedback pulses from the DC evaporator fan motor for more than 2 minutes.

View Diagnostic Tree β†’
Code ERR 02refrigerator

GE ERR 02

The main electronic control board detects an open or shorted thermistor circuit in the fresh food refrigerator compartment (resistance reading out of range).

View Diagnostic Tree β†’
Code 26washer

GE 26

The main electronic control board detected an unrecoverable unbalanced load condition during the spin cycle, tripping the optical or 3D accelerometer balance sensor.

View Diagnostic Tree β†’
Code 3washer

GE 3

The washer control board failed to sense the tub water level dropping to empty within 7 minutes of drain pump activation.

View Diagnostic Tree β†’

LG Fault Codes

10 Documented Codes
Code AEdishwasher

LG AE

The safety float sensor switch mounted in the bottom plastic drip tray detected standing water, halting cycle operation and running drain pump continuously.

View Diagnostic Tree β†’
Code OEdishwasher

LG OE

The main control board detected that water level did not drop below empty threshold after drain pump ran during drain interval.

View Diagnostic Tree β†’
Code d90dryer

LG d90

LG FlowSense duct monitor detects that 90% of the dryer's exhaust airflow is blocked by lint accumulation, crushed venting, or a stuck exterior damper.

View Diagnostic Tree β†’
Code tE1dryer

LG tE1

The main electronic control board detects that the exhaust thermistor sensor circuit resistance is either zero ohms (short circuit) or infinite ohms (open circuit), preventing temperature regulation.

View Diagnostic Tree β†’
Code F3oven range

LG F3

The main electronic oven PCB detects an open circuit in the oven temperature sensor probe circuit during heating operation.

View Diagnostic Tree β†’
Code F9oven range

LG F9

The main electronic oven control board detects that the oven cavity temperature failed to rise above 150Β°F (65Β°C) within 5 to 7 minutes after initiating a Bake, Broil, or Convection cycle.

View Diagnostic Tree β†’
Code Er dHrefrigerator

LG Er dH

The evaporator defrost thermistor did not rise above 41Β°F (5Β°C) within 80 minutes of the defrost heater being energized by the main control board.

View Diagnostic Tree β†’
Code Er FFrefrigerator

LG Er FF

The main control board does not receive rotational feedback pulses (RPM signal) from the freezer evaporator fan motor for more than 115 seconds during compressor run.

View Diagnostic Tree β†’
Code LEwasher

LG LE

The main PCB detects that the direct drive motor rotor is locked, overloaded, or the Hall effect rotor position sensor (RPS) is sending erratic feedback signals.

View Diagnostic Tree β†’
Code OEwasher

LG OE

The electronic main board detected that the washer did not drain the tub water below reset frequency within 10 minutes of starting the drain cycle.

View Diagnostic Tree β†’

Samsung Fault Codes

10 Documented Codes
Code 4Cdishwasher

Samsung 4C

The main control board detects that water did not enter the dishwasher tub to operating level within the timeout period, or the flow meter sensor failed to register pulses.

View Diagnostic Tree β†’
Code LCdishwasher

Samsung LC

The moisture leak sensor located in the bottom drip tray pan detects water or conductive liquid, locking the dishwasher in continuous drain mode to prevent flooding.

View Diagnostic Tree β†’
Code FEdryer

Samsung FE

The main electronic control board detects that the incoming AC electrical supply frequency does not match 60Hz (typical for North America), indicating noisy power or board defect.

View Diagnostic Tree β†’
Code hEdryer

Samsung hE

The dryer detects an invalid heating conditionβ€”either temperature rising too fast due to blocked exhaust or no heat generated due to an open element or tripped thermal limit.

View Diagnostic Tree β†’
Code C-20oven range

Samsung C-20

The main electronic oven control PBA board detects an open circuit or reading above 400Β°C from the oven cavity temperature sensor (RTD probe).

View Diagnostic Tree β†’
Code C-21oven range

Samsung C-21

The electronic control board detects an open or shorted sub-temperature sensor or temperature sensing circuit fault in double-oven / duo-flex partition cavity models.

View Diagnostic Tree β†’
Code 22Erefrigerator

Samsung 22E

The main control board detects a lack of RPM feedback signal pulses from the fresh food compartment evaporator fan motor, frequently caused by frost buildup around fan blades.

View Diagnostic Tree β†’
Code 25Erefrigerator

Samsung 25E

The main electronic control board senses that the fresh food evaporator defrost heater failed to heat the evaporator sensor above target cutoff temperature during defrost cycle.

View Diagnostic Tree β†’
Code 4Cwasher

Samsung 4C

The electronic control module detects that water is not entering the tub or water level has not reached target threshold after 10 minutes of valve activation.

View Diagnostic Tree β†’
Code 5Cwasher

Samsung 5C

The washer fails to drain the wash water below the empty water level reset point within 10 to 15 minutes of drain pump activation.

View Diagnostic Tree β†’

Whirlpool Fault Codes

10 Documented Codes
Code F6E4dishwasher

Whirlpool F6E4

The float switch circuit is detected open during cycle operation, indicating that the overfill safety float has tripped or the base drip pan leak detection float is engaged.

View Diagnostic Tree β†’
Code F8E1dishwasher

Whirlpool F8E1

The electronic control board detects that the wash tub did not fill to operating depth within the allotted time, or the optical water indicator (OWI) sensed low water level.

View Diagnostic Tree β†’
Code F22dryer

Whirlpool F22

The main electronic control board detects an open or shorted exhaust thermistor circuit (resistance reading exceeds 40,000 ohms or drops below 500 ohms at room temperature).

View Diagnostic Tree β†’
Code F30dryer

Whirlpool F30

The control board senses an excessive temperature rise delta between the inlet and exhaust thermistors, indicating dangerously restricted exhaust airflow.

View Diagnostic Tree β†’
Code F3E0oven range

Whirlpool F3E0

The electronic oven control (EOC) board senses an open circuit in the oven temperature sensor (RTD probe) circuit while bake, broil, or clean cycle is commanded.

View Diagnostic Tree β†’
Code F5E0oven range

Whirlpool F5E0

The electronic control detects that the motorized door latch switch contacts do not open or close within the timeout period during clean cycle initiation or door lock sequence.

View Diagnostic Tree β†’
Code E01refrigerator

Whirlpool E01

The main electronic control board is unable to read temperature resistance from the fresh food compartment thermistor due to an open circuit, short to ground, or sensor drift.

View Diagnostic Tree β†’
Code E02refrigerator

Whirlpool E02

The main electronic control board detects an open or shorted defrost thermistor on the freezer evaporator coil, preventing automated adaptive defrost cycles.

View Diagnostic Tree β†’
Code F02washer

Whirlpool F02

The central control unit (CCU) detected that the drain pump ran for longer than 8 minutes without the pressure transducer signaling an empty water level.

View Diagnostic Tree β†’
Code F08washer

Whirlpool F08

The machine detects that water level has not reached the minimum target threshold after 13 minutes of continuous inlet valve actuation.

View Diagnostic Tree β†’
Dispatch: (945) 206-7476 Urgent: (855) 796-2411