Bosch Factory Service ManualFault Code: E24

Bosch Dishwasher Error Code E24: Drain Sequence Timeout / Check Non-Return Valve

The main power module senses abnormal current draw or incomplete water evacuation from the BLDC synchronous drain pump during the initial 1-minute pre-drain sequence, usually caused by a loose impeller cap, blocked non-return valve, or pinched drain line.

OEM Brand: BoschAppliance: dishwasherVerified OEM Diagnostics
Bosch dishwasher diagnostic bench testing and technical inspection for error code E24
Bosch DISHWASHER Diagnostic BenchCODE: E24
Target Appliance

dishwasher

OEM Certified Technical Diagnostic Tree

Diagnostic Tool Required

Digital Multimeter

Measure Ohms resistance, continuity & line voltage.

Triage Complexity

Advanced Diagnostic

5 Sequential manufacturer inspection branches.

Sequential Factory Diagnostic Tree

Perform each diagnostic step in order. Disconnect electrical power and turn off utility shutoffs before inspecting wiring or internal mechanical assemblies.

Digital multimeter measuring ohms resistance and terminal pin continuity on appliance electronic control board
Bench Testing Protocol

Multimeter Resistance & Continuity Verification

Before replacing any electronic control board or mechanical sensor, disconnect power and measure terminal resistance using a calibrated digital multimeter. Verify continuity (0 Ω) across safety switches and compare sensor resistance against OEM specs in the diagnostic steps below.

Step 1: Physical & Electrical InspectionMultimeter & Visual
Action: Examine the white plastic drain pump impeller cover cap in the bottom of the stainless sump (located directly below the removable micro-mesh filter).
Bench Test: Verify that the white plastic cover cap is firmly hooked under the rear retention tab and snapped locked down. (The Bosch drain pump cannot produce hydraulic siphon suction without this cover; a loose or unlatched cover causes immediate cavitation and triggers code E24 within 60 to 90 seconds of cycle start).
Expected Standard: Cover cap is rigidly secured with zero vertical play; snaps in with an audible, firm mechanical click.
If Failed / Out of Spec:

Latching tab is cracked, warped, or unclicked. Resnap firmly or replace OEM Drain Pump Impeller Access Cover Cap (part #00611322).

If Passed:

Impeller cover cap is securely locked. Proceed to Step 2.

Step 2: Physical & Electrical InspectionMultimeter & Visual
Action: Unlatch the white cover cap and inspect the black impeller blades and sump chamber for mechanical obstructions.
Bench Test: Use a wooden stick or gloved finger to rotate the four impeller blades. Check for broken glass splinters, lemon seeds, twist ties, or dental floss coiled around the rotor shaft.
Expected Standard: Impeller rotates freely with notched magnetic resistance (notched spring detents every 90 degrees) and zero physical binding.
If Failed / Out of Spec:

Remove foreign debris using needle-nose pliers and rinse chamber thoroughly with warm water.

If Passed:

Impeller rotates smoothly with proper magnetic detents. Proceed to Step 3.

Step 3: Physical & Electrical InspectionMultimeter & Visual
Action: Remove and inspect the rubber non-return check valve flapper situated directly behind the drain pump chamber in the left-hand sump passage.
Bench Test: Pinch the rubber tab and pull the check valve upward out of its retention slot. Inspect for edge curling, tears, hard mineral scale, or food residue trapped between the flap and seat.
Expected Standard: Soft, completely flat rubber flapper that seals airtight against the plastic seat to prevent dirty sink water from back-siphoning into the dishwasher tub.
If Failed / Out of Spec:

Clean rubber flap and seat thoroughly with rubbing alcohol. If rubber is curled or torn, replace Non-Return Check Valve Flapper (part #00165262).

If Passed:

Check valve is flat and functional. Proceed to Step 4.

Step 4: Physical & Electrical InspectionMultimeter & Visual
Action: Inspect the under-sink corrugated drain hose installation, high-loop elevation, and connection to the garbage disposal or sink tailpiece.
Bench Test: Verify that the drain hose is elevated to the underside of the countertop (minimum 32 inches above floor grade) before descending to the disposal inlet, and verify the disposal knockout plug is completely removed.
Expected Standard: Hose maintains a clean continuous high loop with zero tight kinks, crushing, or sludge buildup inside the disposal nipple.
If Failed / Out of Spec:

Clear disposal nipple restriction with a small screwdriver or re-hang hose into proper high loop bracket.

If Passed:

External plumbing path is 100% clear. Proceed to Step 5.

Step 5: Physical & Electrical InspectionMultimeter & Visual
Action: Perform electrical 3-phase winding resistance bench test on the BLDC synchronous drain pump motor.
Bench Test: Disconnect 3-wire plug from the drain pump motor. Set digital multimeter to lowest Ohms (200Ω) scale and measure resistance between all three motor pin pairs: pins 1 to 2, pins 2 to 3, and pins 1 to 3.
Expected Standard: All three winding measurements must be identical, reading between 75 and 95 ohms (typically ~80–88Ω at 68°F). Any zero-ohm reading (short) or infinite reading (open coil) indicates a burnt motor winding.
If Failed / Out of Spec:

Replace BLDC Synchronous Drain Pump Motor (part #00631200 / 00645038).

If Passed:

Pump windings are balanced and in spec; replace Main Power Control Module PCB (part #11028637) due to failed inverter driver circuit.

Verified OEM Replacement Parts

Cross-referenced factory part numbers for Bosch dishwasher error code E24. Always replace defective components with authentic OEM parts to maintain UL safety certification.

Component NameOEM Part NumberManufacturerStatus
BLDC Synchronous Drain Pump Motor00631200BoschDirect Fit OEM
Drain Pump Impeller Access Cover Cap00611322BoschDirect Fit OEM
Non-Return Check Valve Flapper00165262BoschDirect Fit OEM
Sump Micro-Filter Screen Assembly00645038BoschDirect Fit OEM
Main Power Control Module PCB11028637BoschDirect Fit OEM

Estimated Repair Cost Ranges: Bosch E24

Repair costs for Bosch dishwashers displaying error code E24 vary based on component damage, accessibility, and whether you self-install or dispatch a local factory-trained technician.

DIY Replacement Part

$140 – $340

Direct OEM replacement part cost (excluding tools, shipping, or diagnostic meter equipment).

Pro Diagnostic Fee

$89 – $149

Standard in-home diagnostic evaluation fee by an independent technician (typically applied toward repair).

Total Pro Repair Range

$320 – $590

Typical total job cost including in-home diagnostic, authentic OEM parts, and professional labor (60–120 mins).

Pricing & Diagnostic Disclosure:

The pricing figures provided above represent broad industry averages based on nationwide market surveys and component replacement requirements. Pricing depends on multiple factors including the specific appliance brand, age, mechanical condition, diagnostic complexity, accessibility, and local labor rates. All independent repair contractors set their own independent rates and fee structures. An in-home diagnostic evaluation by an authorized technician is required to provide an exact written quote prior to any repair work.

Related Symptom Triage Guides for Bosch dishwashers

If your appliance displays code E24 alongside physical operational symptoms, consult our dedicated failure triage flowcharts:

Symptom Triage

Why Is My Dishwasher Leaking Water onto the Floor?

View Triage Flowchart →
Symptom Triage

Why Is My Dishwasher Making a Loud Grinding Noise? Diagnostic Guide

View Triage Flowchart →
Symptom Triage

Why Is My Dishwasher Not Cleaning Dishes Properly?

View Triage Flowchart →
Symptom Triage

Why Is My Dishwasher Not Dissolving the Detergent Tablet? Causes & Fixes

View Triage Flowchart →
Engineering Service Hub

Looking for Full Dishwasher Repair Procedures?

Explore comprehensive diagnostic mechanics, component resistance curves, and EPA guidelines for Bosch units.

Dishwasher Repair Specs →
Local In-Home Diagnostic Dispatch

Tired of Troubleshooting Code E24? Get a Local Bosch Technician.

If multimeter bench tests confirm component failure or you prefer a professional to safely service your high-voltage Bosch dishwasher, connect with an independent certified specialist in Colorado, Kansas, or New Mexico today.

(945) 206-7476 Urgent: (855) 796-2411Mon-Sun 7am–9pm • Fast Local Dispatch
Local In-Home Service DispatchSame-Day Available

Need In-Home Diagnostic Dispatch for Code E24?

If multimeter testing confirms an internal short, failed heating element, locked motor, or burnt control board on your Bosch dishwasher, connect with an independent certified technician in your city.

dishwasher repair in Olathe, KS
Olathe, KS Dispatch Hub
→
dishwasher repair in Overland Park, KS
Overland Park, KS Dispatch Hub
→
dishwasher repair in Wichita, KS
Wichita, KS Dispatch Hub
→
dishwasher repair in Lawrence, KS
Lawrence, KS Dispatch Hub
→
dishwasher repair in Topeka, KS
Topeka, KS Dispatch Hub
→
dishwasher repair in Kansas City, KS
Kansas City, KS Dispatch Hub
→
dishwasher repair in Denver, CO
Denver, CO Dispatch Hub
→
dishwasher repair in Colorado Springs, CO
Colorado Springs, CO Dispatch Hub
→
dishwasher repair in Aurora, CO
Aurora, CO Dispatch Hub
→
dishwasher repair in Fort Collins, CO
Fort Collins, CO Dispatch Hub
→
dishwasher repair in Lakewood, CO
Lakewood, CO Dispatch Hub
→
dishwasher repair in Boulder, CO
Boulder, CO Dispatch Hub
→
dishwasher repair in Albuquerque, NM
Albuquerque, NM Dispatch Hub
→
dishwasher repair in Las Cruces, NM
Las Cruces, NM Dispatch Hub
→
dishwasher repair in Rio Rancho, NM
Rio Rancho, NM Dispatch Hub
→
Serving over 120+ cities across Colorado, Kansas, and New Mexico. View all municipal service areas →
Dispatch: (945) 206-7476 Urgent Scenario: (855) 796-2411

Frequently Asked Questions: Bosch E24

What causes Bosch dishwasher error code E24?

The main power module senses abnormal current draw or incomplete water evacuation from the BLDC synchronous drain pump during the initial 1-minute pre-drain sequence, usually caused by a loose impeller cap, blocked non-return valve, or pinched drain line.

Can I reset the E24 code by unplugging the dishwasher?

While disconnecting power for 5 minutes may temporarily clear the display control memory, the E24 code will reoccur once the microcontroller detects the mechanical or electrical fault again.

What OEM replacement parts are required for Bosch E24?

Common OEM replacement components include: BLDC Synchronous Drain Pump Motor (OEM #00631200), Drain Pump Impeller Access Cover Cap (OEM #00611322), Non-Return Check Valve Flapper (OEM #00165262), Sump Micro-Filter Screen Assembly (OEM #00645038), Main Power Control Module PCB (OEM #11028637).

How much does it cost to fix Bosch dishwasher error code E24?

Professional repair for Bosch dishwasher error code E24 typically averages $320 – $590 in total (including an estimated diagnostic fee of $89 – $149 plus labor and authentic OEM components). Sourcing authentic replacement parts yourself costs approximately $140 – $340. Final prices depend on model specifics, local labor rates, and physical technician inspection.

Dispatch: (945) 206-7476 Urgent: (855) 796-2411