Frigidaire Factory Service ManualFault Code: E11

Frigidaire Washer Error Code E11: Fill Time Too Long / Low Water Level

The main electronic control board detects that the wash tub did not reach the target water level within 8 minutes of water inlet valve opening.

OEM Brand: FrigidaireAppliance: washerVerified OEM Diagnostics
Frigidaire washer diagnostic bench testing and technical inspection for error code E11
Frigidaire WASHER Diagnostic BenchCODE: E11
Target Appliance

washer

OEM Certified Technical Diagnostic Tree

Diagnostic Tool Required

Digital Multimeter

Measure Ohms resistance, continuity & line voltage.

Triage Complexity

Advanced Diagnostic

4 Sequential manufacturer inspection branches.

Sequential Factory Diagnostic Tree

Perform each diagnostic step in order. Disconnect electrical power and turn off utility shutoffs before inspecting wiring or internal mechanical assemblies.

Digital multimeter measuring ohms resistance and terminal pin continuity on appliance electronic control board
Bench Testing Protocol

Multimeter Resistance & Continuity Verification

Before replacing any electronic control board or mechanical sensor, disconnect power and measure terminal resistance using a calibrated digital multimeter. Verify continuity (0 ฮฉ) across safety switches and compare sensor resistance against OEM specs in the diagnostic steps below.

Step 1: Physical & Electrical InspectionMultimeter & Visual
Action: Verify that both hot and cold water shutoff valves behind the washer are turned fully on.
Bench Test: Disconnect supply hoses from washer into a 5-gallon bucket and test municipal water flow rate.
Expected Standard: Strong flow rate of at least 3.0 gallons per minute at 20โ€“100 PSI.
If Failed / Out of Spec:

Open supply valves fully, thaw frozen pipes, or replace kinked water supply hoses.

If Passed:

Proceed to Step 2.

Step 2: Physical & Electrical InspectionMultimeter & Visual
Action: Disconnect hoses from water inlet valve ports on rear panel and inspect mesh filter screens.
Bench Test: Visually inspect cold and hot inlet valve debris screens for calcium, sediment, or mineral buildup.
Expected Standard: Mesh screens completely clean and free of particulate debris.
If Failed / Out of Spec:

Extract and clean sediment screens with a soft brush; flush hoses before reattaching.

If Passed:

Proceed to Step 3.

Step 3: Physical & Electrical InspectionMultimeter & Visual
Action: Disconnect wiring harness from water inlet valve solenoids and measure coil resistance with multimeter.
Bench Test: Measure DC resistance across each solenoid coil terminal set with multimeter set to ohms.
Expected Standard: Between 800 and 1,200 ohms across each solenoid coil.
If Failed / Out of Spec:

Replace water inlet valve assembly (134637810).

If Passed:

Proceed to Step 4.

Step 4: Physical & Electrical InspectionMultimeter & Visual
Action: Inspect pressure switch air tube and pressure transducer on the upper cabinet frame.
Bench Test: Check air tube for pinholes, loose barb fitting, or soap froth foam intrusion.
Expected Standard: Airtight connection; valid frequency output at pressure switch pins.
If Failed / Out of Spec:

Replace pressure switch tube or water level pressure sensor switch (134762010).

If Passed:

Replace main electronic control board (137006000) due to failed inlet valve relay circuit.

Verified OEM Replacement Parts

Cross-referenced factory part numbers for Frigidaire washer error code E11. Always replace defective components with authentic OEM parts to maintain UL safety certification.

Component NameOEM Part NumberManufacturerStatus
Water Inlet Valve Assembly134637810FrigidaireDirect Fit OEM
Water Level Pressure Sensor Switch134762010FrigidaireDirect Fit OEM
Main Electronic Control Board137006000FrigidaireDirect Fit OEM

Estimated Repair Cost Ranges: Frigidaire E11

Repair costs for Frigidaire washers displaying error code E11 vary based on component damage, accessibility, and whether you self-install or dispatch a local factory-trained technician.

DIY Replacement Part

$140 โ€“ $340

Direct OEM replacement part cost (excluding tools, shipping, or diagnostic meter equipment).

Pro Diagnostic Fee

$89 โ€“ $149

Standard in-home diagnostic evaluation fee by an independent technician (typically applied toward repair).

Total Pro Repair Range

$320 โ€“ $590

Typical total job cost including in-home diagnostic, authentic OEM parts, and professional labor (60โ€“120 mins).

Pricing & Diagnostic Disclosure:

The pricing figures provided above represent broad industry averages based on nationwide market surveys and component replacement requirements. Pricing depends on multiple factors including the specific appliance brand, age, mechanical condition, diagnostic complexity, accessibility, and local labor rates. All independent repair contractors set their own independent rates and fee structures. An in-home diagnostic evaluation by an authorized technician is required to provide an exact written quote prior to any repair work.

Related Symptom Triage Guides for Frigidaire washers

If your appliance displays code E11 alongside physical operational symptoms, consult our dedicated failure triage flowcharts:

Symptom Triage

Why Are Clothes Still Soaking Wet After the Washer Spin Cycle?

View Triage Flowchart โ†’
Symptom Triage

Why Does My Washing Machine Smell Like Mildew or Rotten Eggs?

View Triage Flowchart โ†’
Symptom Triage

Why Is My Front Load Washer Door Locked and Won't Open? Diagnostics

View Triage Flowchart โ†’
Symptom Triage

Why Is My Washing Machine Leaking Water? Diagnostic Guide

View Triage Flowchart โ†’
Engineering Service Hub

Looking for Full Washing Machine Repair Procedures?

Explore comprehensive diagnostic mechanics, component resistance curves, and EPA guidelines for Frigidaire units.

Washing Machine Repair Specs โ†’
Local In-Home Diagnostic Dispatch

Tired of Troubleshooting Code E11? Get a Local Frigidaire Technician.

If multimeter bench tests confirm component failure or you prefer a professional to safely service your high-voltage Frigidaire washer, connect with an independent certified specialist in Colorado, Kansas, or New Mexico today.

(945) 206-7476 Urgent: (855) 796-2411Mon-Sun 7amโ€“9pm โ€ข Fast Local Dispatch
Local In-Home Service DispatchSame-Day Available

Need In-Home Diagnostic Dispatch for Code E11?

If multimeter testing confirms an internal short, failed heating element, locked motor, or burnt control board on your Frigidaire washer, connect with an independent certified technician in your city.

washing machine repair in Olathe, KS
Olathe, KS Dispatch Hub
โ†’
washing machine repair in Overland Park, KS
Overland Park, KS Dispatch Hub
โ†’
washing machine repair in Wichita, KS
Wichita, KS Dispatch Hub
โ†’
washing machine repair in Lawrence, KS
Lawrence, KS Dispatch Hub
โ†’
washing machine repair in Topeka, KS
Topeka, KS Dispatch Hub
โ†’
washing machine repair in Kansas City, KS
Kansas City, KS Dispatch Hub
โ†’
washing machine repair in Denver, CO
Denver, CO Dispatch Hub
โ†’
washing machine repair in Colorado Springs, CO
Colorado Springs, CO Dispatch Hub
โ†’
washing machine repair in Aurora, CO
Aurora, CO Dispatch Hub
โ†’
washing machine repair in Fort Collins, CO
Fort Collins, CO Dispatch Hub
โ†’
washing machine repair in Lakewood, CO
Lakewood, CO Dispatch Hub
โ†’
washing machine repair in Boulder, CO
Boulder, CO Dispatch Hub
โ†’
washing machine repair in Albuquerque, NM
Albuquerque, NM Dispatch Hub
โ†’
washing machine repair in Las Cruces, NM
Las Cruces, NM Dispatch Hub
โ†’
washing machine repair in Rio Rancho, NM
Rio Rancho, NM Dispatch Hub
โ†’
Serving over 120+ cities across Colorado, Kansas, and New Mexico. View all municipal service areas โ†’
Dispatch: (945) 206-7476 Urgent Scenario: (855) 796-2411

Frequently Asked Questions: Frigidaire E11

What causes Frigidaire washer error code E11?

The main electronic control board detects that the wash tub did not reach the target water level within 8 minutes of water inlet valve opening.

Can I reset the E11 code by unplugging the washer?

While disconnecting power for 5 minutes may temporarily clear the display control memory, the E11 code will reoccur once the microcontroller detects the mechanical or electrical fault again.

What OEM replacement parts are required for Frigidaire E11?

Common OEM replacement components include: Water Inlet Valve Assembly (OEM #134637810), Water Level Pressure Sensor Switch (OEM #134762010), Main Electronic Control Board (OEM #137006000).

How much does it cost to fix Frigidaire washer error code E11?

Professional repair for Frigidaire washer error code E11 typically averages $320 โ€“ $590 in total (including an estimated diagnostic fee of $89 โ€“ $149 plus labor and authentic OEM components). Sourcing authentic replacement parts yourself costs approximately $140 โ€“ $340. Final prices depend on model specifics, local labor rates, and physical technician inspection.

Dispatch: (945) 206-7476 Urgent: (855) 796-2411