Frigidaire Washer Error Code E21: Water Not Draining Fast Enough
The main electronic control board detects that water did not drain from the wash tub within the allowable 4.5-minute drain cycle timeout.
washer
OEM Certified Technical Diagnostic Tree
Digital Multimeter
Measure Ohms resistance, continuity & line voltage.
Advanced Diagnostic
4 Sequential manufacturer inspection branches.
Sequential Factory Diagnostic Tree
Perform each diagnostic step in order. Disconnect electrical power and turn off utility shutoffs before inspecting wiring or internal mechanical assemblies.
Multimeter Resistance & Continuity Verification
Before replacing any electronic control board or mechanical sensor, disconnect power and measure terminal resistance using a calibrated digital multimeter. Verify continuity (0 ฮฉ) across safety switches and compare sensor resistance against OEM specs in the diagnostic steps below.
Clean debris trap chamber, rinse filter under warm water, and replace filter plug tightly.
Proceed to Step 2.
Straighten drain hose, pull back from standpipe, or snake house drain plumbing.
Proceed to Step 3.
Replace drain pump motor assembly (137221600).
Proceed to Step 4.
Clean air dome chamber or replace water level pressure sensor switch (134762010).
Replace main electronic control board (137006000) due to failed drain pump triac.
Verified OEM Replacement Parts
Cross-referenced factory part numbers for Frigidaire washer error code E21. Always replace defective components with authentic OEM parts to maintain UL safety certification.
| Component Name | OEM Part Number | Manufacturer | Status |
|---|---|---|---|
| Drain Pump Motor Assembly | 137221600 | Frigidaire | Direct Fit OEM |
| Water Level Pressure Sensor Switch | 134762010 | Frigidaire | Direct Fit OEM |
| Main Electronic Control Board | 137006000 | Frigidaire | Direct Fit OEM |
Estimated Repair Cost Ranges: Frigidaire E21
Repair costs for Frigidaire washers displaying error code E21 vary based on component damage, accessibility, and whether you self-install or dispatch a local factory-trained technician.
$140 โ $340
Direct OEM replacement part cost (excluding tools, shipping, or diagnostic meter equipment).
$89 โ $149
Standard in-home diagnostic evaluation fee by an independent technician (typically applied toward repair).
$320 โ $590
Typical total job cost including in-home diagnostic, authentic OEM parts, and professional labor (60โ120 mins).
Pricing & Diagnostic Disclosure:
The pricing figures provided above represent broad industry averages based on nationwide market surveys and component replacement requirements. Pricing depends on multiple factors including the specific appliance brand, age, mechanical condition, diagnostic complexity, accessibility, and local labor rates. All independent repair contractors set their own independent rates and fee structures. An in-home diagnostic evaluation by an authorized technician is required to provide an exact written quote prior to any repair work.
Related Symptom Triage Guides for Frigidaire washers
If your appliance displays code E21 alongside physical operational symptoms, consult our dedicated failure triage flowcharts:
Why Are Clothes Still Soaking Wet After the Washer Spin Cycle?
Why Does My Washing Machine Smell Like Mildew or Rotten Eggs?
Why Is My Front Load Washer Door Locked and Won't Open? Diagnostics
Why Is My Washing Machine Leaking Water? Diagnostic Guide
Looking for Full Washing Machine Repair Procedures?
Explore comprehensive diagnostic mechanics, component resistance curves, and EPA guidelines for Frigidaire units.
Need In-Home Diagnostic Dispatch for Code E21?
If multimeter testing confirms an internal short, failed heating element, locked motor, or burnt control board on your Frigidaire washer, connect with an independent certified technician in your city.
Frequently Asked Questions: Frigidaire E21
What causes Frigidaire washer error code E21?
The main electronic control board detects that water did not drain from the wash tub within the allowable 4.5-minute drain cycle timeout.
Can I reset the E21 code by unplugging the washer?
While disconnecting power for 5 minutes may temporarily clear the display control memory, the E21 code will reoccur once the microcontroller detects the mechanical or electrical fault again.
What OEM replacement parts are required for Frigidaire E21?
Common OEM replacement components include: Drain Pump Motor Assembly (OEM #137221600), Water Level Pressure Sensor Switch (OEM #134762010), Main Electronic Control Board (OEM #137006000).
How much does it cost to fix Frigidaire washer error code E21?
Professional repair for Frigidaire washer error code E21 typically averages $320 โ $590 in total (including an estimated diagnostic fee of $89 โ $149 plus labor and authentic OEM components). Sourcing authentic replacement parts yourself costs approximately $140 โ $340. Final prices depend on model specifics, local labor rates, and physical technician inspection.

