Frigidaire Factory Service ManualFault Code: E43

Frigidaire Washer Error Code E43: Door Lock PTC Wax Motor / Triac Drive Fault

The main control board detects a shorted or failed PTC heating element inside the door lock assembly or a burned board lock triac.

OEM Brand: FrigidaireAppliance: washerVerified OEM Diagnostics
Frigidaire washer diagnostic bench testing and technical inspection for error code E43
Frigidaire WASHER Diagnostic BenchCODE: E43
Target Appliance

washer

OEM Certified Technical Diagnostic Tree

Diagnostic Tool Required

Digital Multimeter

Measure Ohms resistance, continuity & line voltage.

Triage Complexity

Advanced Diagnostic

4 Sequential manufacturer inspection branches.

Sequential Factory Diagnostic Tree

Perform each diagnostic step in order. Disconnect electrical power and turn off utility shutoffs before inspecting wiring or internal mechanical assemblies.

Digital multimeter measuring ohms resistance and terminal pin continuity on appliance electronic control board
Bench Testing Protocol

Multimeter Resistance & Continuity Verification

Before replacing any electronic control board or mechanical sensor, disconnect power and measure terminal resistance using a calibrated digital multimeter. Verify continuity (0 ฮฉ) across safety switches and compare sensor resistance against OEM specs in the diagnostic steps below.

Step 1: Physical & Electrical InspectionMultimeter & Visual
Action: Disconnect power, remove top panel, and locate the door lock connector.
Bench Test: Measure electrical resistance across the door lock PTC wax motor / solenoid terminals.
Expected Standard: Normal resistance is approximately 1,100 to 1,500 ohms (1.1kโ€“1.5k ฮฉ) at room temperature.
If Failed / Out of Spec:

Shorted or open PTC element (< 500 ohms or 0L). Replace door lock switch (134629900).

If Passed:

Proceed to Step 2.

Step 2: Physical & Electrical InspectionMultimeter & Visual
Action: Inspect the door lock wire harness for thermal discoloration or pinched insulation.
Bench Test: Measure resistance of all harness leads end-to-end.
Expected Standard: 0 ohms continuity; clean pins.
If Failed / Out of Spec:

Repair harness wiring.

If Passed:

Proceed to Step 3.

Step 3: Physical & Electrical InspectionMultimeter & Visual
Action: Inspect the main electronic control board for a visibly burned door lock triac (component Q8 or similar).
Bench Test: Examine the surface of the triac chip for physical pitting, black soot, or blown casing.
Expected Standard: Triac pristine with zero burn marks or board charring.
If Failed / Out of Spec:

A shorted PTC wax motor frequently destroys the board triac. Replace both door lock (134629900) AND main control board (137006000).

If Passed:

Proceed to Step 4.

Step 4: Physical & Electrical InspectionMultimeter & Visual
Action: Test door lock engagement under service test mode.
Bench Test: Initiate service test code 03 to command door lock activation.
Expected Standard: Lock clicks and door cannot be opened within 5 seconds.
If Failed / Out of Spec:

Replace main electronic control board (137006000).

If Passed:

Clear error code from non-volatile memory.

Verified OEM Replacement Parts

Cross-referenced factory part numbers for Frigidaire washer error code E43. Always replace defective components with authentic OEM parts to maintain UL safety certification.

Component NameOEM Part NumberManufacturerStatus
Door Lock & Switch Assembly134629900FrigidaireDirect Fit OEM
Main Electronic Control Board137006000FrigidaireDirect Fit OEM
Door Strike Assembly134456600FrigidaireDirect Fit OEM

Estimated Repair Cost Ranges: Frigidaire E43

Repair costs for Frigidaire washers displaying error code E43 vary based on component damage, accessibility, and whether you self-install or dispatch a local factory-trained technician.

DIY Replacement Part

$140 โ€“ $340

Direct OEM replacement part cost (excluding tools, shipping, or diagnostic meter equipment).

Pro Diagnostic Fee

$89 โ€“ $149

Standard in-home diagnostic evaluation fee by an independent technician (typically applied toward repair).

Total Pro Repair Range

$320 โ€“ $590

Typical total job cost including in-home diagnostic, authentic OEM parts, and professional labor (60โ€“120 mins).

Pricing & Diagnostic Disclosure:

The pricing figures provided above represent broad industry averages based on nationwide market surveys and component replacement requirements. Pricing depends on multiple factors including the specific appliance brand, age, mechanical condition, diagnostic complexity, accessibility, and local labor rates. All independent repair contractors set their own independent rates and fee structures. An in-home diagnostic evaluation by an authorized technician is required to provide an exact written quote prior to any repair work.

Related Symptom Triage Guides for Frigidaire washers

If your appliance displays code E43 alongside physical operational symptoms, consult our dedicated failure triage flowcharts:

Symptom Triage

Why Are Clothes Still Soaking Wet After the Washer Spin Cycle?

View Triage Flowchart โ†’
Symptom Triage

Why Does My Washing Machine Smell Like Mildew or Rotten Eggs?

View Triage Flowchart โ†’
Symptom Triage

Why Is My Front Load Washer Door Locked and Won't Open? Diagnostics

View Triage Flowchart โ†’
Symptom Triage

Why Is My Washing Machine Leaking Water? Diagnostic Guide

View Triage Flowchart โ†’
Engineering Service Hub

Looking for Full Washing Machine Repair Procedures?

Explore comprehensive diagnostic mechanics, component resistance curves, and EPA guidelines for Frigidaire units.

Washing Machine Repair Specs โ†’
Local In-Home Diagnostic Dispatch

Tired of Troubleshooting Code E43? Get a Local Frigidaire Technician.

If multimeter bench tests confirm component failure or you prefer a professional to safely service your high-voltage Frigidaire washer, connect with an independent certified specialist in Colorado, Kansas, or New Mexico today.

(945) 206-7476 Urgent: (855) 796-2411Mon-Sun 7amโ€“9pm โ€ข Fast Local Dispatch
Local In-Home Service DispatchSame-Day Available

Need In-Home Diagnostic Dispatch for Code E43?

If multimeter testing confirms an internal short, failed heating element, locked motor, or burnt control board on your Frigidaire washer, connect with an independent certified technician in your city.

washing machine repair in Olathe, KS
Olathe, KS Dispatch Hub
โ†’
washing machine repair in Overland Park, KS
Overland Park, KS Dispatch Hub
โ†’
washing machine repair in Wichita, KS
Wichita, KS Dispatch Hub
โ†’
washing machine repair in Lawrence, KS
Lawrence, KS Dispatch Hub
โ†’
washing machine repair in Topeka, KS
Topeka, KS Dispatch Hub
โ†’
washing machine repair in Kansas City, KS
Kansas City, KS Dispatch Hub
โ†’
washing machine repair in Denver, CO
Denver, CO Dispatch Hub
โ†’
washing machine repair in Colorado Springs, CO
Colorado Springs, CO Dispatch Hub
โ†’
washing machine repair in Aurora, CO
Aurora, CO Dispatch Hub
โ†’
washing machine repair in Fort Collins, CO
Fort Collins, CO Dispatch Hub
โ†’
washing machine repair in Lakewood, CO
Lakewood, CO Dispatch Hub
โ†’
washing machine repair in Boulder, CO
Boulder, CO Dispatch Hub
โ†’
washing machine repair in Albuquerque, NM
Albuquerque, NM Dispatch Hub
โ†’
washing machine repair in Las Cruces, NM
Las Cruces, NM Dispatch Hub
โ†’
washing machine repair in Rio Rancho, NM
Rio Rancho, NM Dispatch Hub
โ†’
Serving over 120+ cities across Colorado, Kansas, and New Mexico. View all municipal service areas โ†’
Dispatch: (945) 206-7476 Urgent Scenario: (855) 796-2411

Frequently Asked Questions: Frigidaire E43

What causes Frigidaire washer error code E43?

The main control board detects a shorted or failed PTC heating element inside the door lock assembly or a burned board lock triac.

Can I reset the E43 code by unplugging the washer?

While disconnecting power for 5 minutes may temporarily clear the display control memory, the E43 code will reoccur once the microcontroller detects the mechanical or electrical fault again.

What OEM replacement parts are required for Frigidaire E43?

Common OEM replacement components include: Door Lock & Switch Assembly (OEM #134629900), Main Electronic Control Board (OEM #137006000), Door Strike Assembly (OEM #134456600).

How much does it cost to fix Frigidaire washer error code E43?

Professional repair for Frigidaire washer error code E43 typically averages $320 โ€“ $590 in total (including an estimated diagnostic fee of $89 โ€“ $149 plus labor and authentic OEM components). Sourcing authentic replacement parts yourself costs approximately $140 โ€“ $340. Final prices depend on model specifics, local labor rates, and physical technician inspection.

Dispatch: (945) 206-7476 Urgent: (855) 796-2411