LG Factory Service ManualFault Code: F3

LG Range / Oven Error Code F3: Oven Cavity Thermistor Open Circuit

The main electronic oven PCB detects an open circuit in the oven temperature sensor probe circuit during heating operation.

OEM Brand: LGAppliance: oven rangeVerified OEM Diagnostics
LG oven-range diagnostic bench testing and technical inspection for error code F3
LG OVEN-RANGE Diagnostic BenchCODE: F3
Target Appliance

oven range

OEM Certified Technical Diagnostic Tree

Diagnostic Tool Required

Digital Multimeter

Measure Ohms resistance, continuity & line voltage.

Triage Complexity

Advanced Diagnostic

4 Sequential manufacturer inspection branches.

Sequential Factory Diagnostic Tree

Perform each diagnostic step in order. Disconnect electrical power and turn off utility shutoffs before inspecting wiring or internal mechanical assemblies.

Digital multimeter measuring ohms resistance and terminal pin continuity on appliance electronic control board
Bench Testing Protocol

Multimeter Resistance & Continuity Verification

Before replacing any electronic control board or mechanical sensor, disconnect power and measure terminal resistance using a calibrated digital multimeter. Verify continuity (0 ฮฉ) across safety switches and compare sensor resistance against OEM specs in the diagnostic steps below.

Step 1: Physical & Electrical InspectionMultimeter & Visual
Action: Disconnect power to range at circuit breaker, remove oven racks, and remove the two mounting screws holding RTD temperature probe to rear cavity.
Bench Test: Inspect probe body for physical damage, bending, or burned wiring pigtails.
Expected Standard: Sensor probe clean with intact ceramic insulation and wiring leads.
If Failed / Out of Spec:

Replace oven cavity temperature sensor probe (EBG61305801).

If Passed:

Proceed to Step 2.

Step 2: Physical & Electrical InspectionMultimeter & Visual
Action: Measure electrical resistance across probe terminals with digital multimeter set to ohms at room temperature (77ยฐF / 25ยฐC).
Bench Test: Measure resistance across the two sensor connector pins.
Expected Standard: Approximately 1,080 to 1,100 ohms at 77ยฐF (1,000 ohm platinum RTD standard).
If Failed / Out of Spec:

Replace temperature sensor probe (EBG61305801) if reading is open (infinity) or out of spec.

If Passed:

Proceed to Step 3.

Step 3: Physical & Electrical InspectionMultimeter & Visual
Action: Remove rear outer metal panel and measure resistance of sensor harness at the main PCB connector CON2.
Bench Test: Measure resistance across sensor pins at the board plug.
Expected Standard: 1,080 to 1,100 ohms matching the reading at probe terminals.
If Failed / Out of Spec:

Repair open circuit in rear wiring harness or replace damaged wiring pin connector.

If Passed:

Proceed to Step 4.

Step 4: Physical & Electrical InspectionMultimeter & Visual
Action: Inspect electronic oven control board PCB for burned traces or cracked solder joints near sensor inputs.
Bench Test: Inspect PCB component board for scorch marks or defective sensing resistors.
Expected Standard: Clean PCB traces with zero thermal distress.
If Failed / Out of Spec:

Replace main electronic oven control board PCB (EBR82260601).

If Passed:

Restore circuit breaker power and verify oven bake cycle operation.

Verified OEM Replacement Parts

Cross-referenced factory part numbers for LG oven-range error code F3. Always replace defective components with authentic OEM parts to maintain UL safety certification.

Component NameOEM Part NumberManufacturerStatus
Oven Temperature Sensor ProbeEBG61305801LGDirect Fit OEM
Electronic Oven Control Board PCBEBR82260601LGDirect Fit OEM
Bake Heating Element AssemblyMEE61841401LGDirect Fit OEM

Estimated Repair Cost Ranges: LG F3

Repair costs for LG oven-ranges displaying error code F3 vary based on component damage, accessibility, and whether you self-install or dispatch a local factory-trained technician.

DIY Replacement Part

$140 โ€“ $340

Direct OEM replacement part cost (excluding tools, shipping, or diagnostic meter equipment).

Pro Diagnostic Fee

$89 โ€“ $149

Standard in-home diagnostic evaluation fee by an independent technician (typically applied toward repair).

Total Pro Repair Range

$320 โ€“ $590

Typical total job cost including in-home diagnostic, authentic OEM parts, and professional labor (60โ€“120 mins).

Pricing & Diagnostic Disclosure:

The pricing figures provided above represent broad industry averages based on nationwide market surveys and component replacement requirements. Pricing depends on multiple factors including the specific appliance brand, age, mechanical condition, diagnostic complexity, accessibility, and local labor rates. All independent repair contractors set their own independent rates and fee structures. An in-home diagnostic evaluation by an authorized technician is required to provide an exact written quote prior to any repair work.

Related Symptom Triage Guides for LG oven-ranges

If your appliance displays code F3 alongside physical operational symptoms, consult our dedicated failure triage flowcharts:

Symptom Triage

Why Does My Gas Oven Igniter Glow Orange but the Burner Won't Ignite?

View Triage Flowchart โ†’
Symptom Triage

Why Does My Oven or Range Smell Like Gas? Emergency Safety Guide

View Triage Flowchart โ†’
Symptom Triage

Why Is My Electric Stove Radiant Burner Not Working?

View Triage Flowchart โ†’
Symptom Triage

Why Is My Gas Stove Burner Clicking and Won't Light?

View Triage Flowchart โ†’
Engineering Service Hub

Looking for Full Oven & Range Repair Procedures?

Explore comprehensive diagnostic mechanics, component resistance curves, and EPA guidelines for LG units.

Oven & Range Repair Specs โ†’
Local In-Home Diagnostic Dispatch

Tired of Troubleshooting Code F3? Get a Local LG Technician.

If multimeter bench tests confirm component failure or you prefer a professional to safely service your high-voltage LG oven-range, connect with an independent certified specialist in Colorado, Kansas, or New Mexico today.

(945) 206-7476 Urgent: (855) 796-2411Mon-Sun 7amโ€“9pm โ€ข Fast Local Dispatch
Local In-Home Service DispatchSame-Day Available

Need In-Home Diagnostic Dispatch for Code F3?

If multimeter testing confirms an internal short, failed heating element, locked motor, or burnt control board on your LG oven-range, connect with an independent certified technician in your city.

oven & range repair in Olathe, KS
Olathe, KS Dispatch Hub
โ†’
oven & range repair in Overland Park, KS
Overland Park, KS Dispatch Hub
โ†’
oven & range repair in Wichita, KS
Wichita, KS Dispatch Hub
โ†’
oven & range repair in Lawrence, KS
Lawrence, KS Dispatch Hub
โ†’
oven & range repair in Topeka, KS
Topeka, KS Dispatch Hub
โ†’
oven & range repair in Kansas City, KS
Kansas City, KS Dispatch Hub
โ†’
oven & range repair in Denver, CO
Denver, CO Dispatch Hub
โ†’
oven & range repair in Colorado Springs, CO
Colorado Springs, CO Dispatch Hub
โ†’
oven & range repair in Aurora, CO
Aurora, CO Dispatch Hub
โ†’
oven & range repair in Fort Collins, CO
Fort Collins, CO Dispatch Hub
โ†’
oven & range repair in Lakewood, CO
Lakewood, CO Dispatch Hub
โ†’
oven & range repair in Boulder, CO
Boulder, CO Dispatch Hub
โ†’
oven & range repair in Albuquerque, NM
Albuquerque, NM Dispatch Hub
โ†’
oven & range repair in Las Cruces, NM
Las Cruces, NM Dispatch Hub
โ†’
oven & range repair in Rio Rancho, NM
Rio Rancho, NM Dispatch Hub
โ†’
Serving over 120+ cities across Colorado, Kansas, and New Mexico. View all municipal service areas โ†’
Dispatch: (945) 206-7476 Urgent Scenario: (855) 796-2411

Frequently Asked Questions: LG F3

What causes LG oven-range error code F3?

The main electronic oven PCB detects an open circuit in the oven temperature sensor probe circuit during heating operation.

Can I reset the F3 code by unplugging the oven-range?

While disconnecting power for 5 minutes may temporarily clear the display control memory, the F3 code will reoccur once the microcontroller detects the mechanical or electrical fault again.

What OEM replacement parts are required for LG F3?

Common OEM replacement components include: Oven Temperature Sensor Probe (OEM #EBG61305801), Electronic Oven Control Board PCB (OEM #EBR82260601), Bake Heating Element Assembly (OEM #MEE61841401).

How much does it cost to fix LG oven-range error code F3?

Professional repair for LG oven-range error code F3 typically averages $320 โ€“ $590 in total (including an estimated diagnostic fee of $89 โ€“ $149 plus labor and authentic OEM components). Sourcing authentic replacement parts yourself costs approximately $140 โ€“ $340. Final prices depend on model specifics, local labor rates, and physical technician inspection.

Dispatch: (945) 206-7476 Urgent: (855) 796-2411