LG Factory Service ManualFault Code: F9

LG Range & Oven Error Code F9: Heating Timeout / Temperature Rise Failure

The main electronic oven control board detects that the oven cavity temperature failed to rise above 150°F (65°C) within 5 to 7 minutes after initiating a Bake, Broil, or Convection cycle.

OEM Brand: LGAppliance: oven rangeVerified OEM Diagnostics
LG oven-range diagnostic bench testing and technical inspection for error code F9
LG OVEN-RANGE Diagnostic BenchCODE: F9
Target Appliance

oven range

OEM Certified Technical Diagnostic Tree

Diagnostic Tool Required

Digital Multimeter

Measure Ohms resistance, continuity & line voltage.

Triage Complexity

Advanced Diagnostic

5 Sequential manufacturer inspection branches.

Sequential Factory Diagnostic Tree

Perform each diagnostic step in order. Disconnect electrical power and turn off utility shutoffs before inspecting wiring or internal mechanical assemblies.

Digital multimeter measuring ohms resistance and terminal pin continuity on appliance electronic control board
Bench Testing Protocol

Multimeter Resistance & Continuity Verification

Before replacing any electronic control board or mechanical sensor, disconnect power and measure terminal resistance using a calibrated digital multimeter. Verify continuity (0 Ω) across safety switches and compare sensor resistance against OEM specs in the diagnostic steps below.

Step 1: Physical & Electrical InspectionMultimeter & Visual
Action: Verify incoming dual-leg electrical supply: For electric ranges, measure line-to-line voltage at the terminal block where the 4-prong/3-prong cord connects. For gas models, confirm 120V AC polarity and verify the manual gas shutoff valve behind the range is 100% open.
Bench Test: Set digital multimeter to AC Volts (600V range) and probe between L1 and L2 terminals on the range junction block.
Expected Standard: 240V AC across L1 and L2 (and 120V AC from L1 to Neutral, 120V AC from L2 to Neutral).
If Failed / Out of Spec:

One leg of the 240V circuit is tripped at the main house breaker panel (allows display clock to operate on 120V while bake element receives no heating voltage). Reset the double-pole 40A or 50A breaker.

If Passed:

Incoming voltage is within spec (230V–245V AC). Proceed to Step 2.

Step 2: Physical & Electrical InspectionMultimeter & Visual
Action: Disconnect electrical power cord from wall outlet. Remove the lower rear metal panel of the range to access the hidden bake heating element terminals (or lower drawer access on slide-in models).
Bench Test: Disconnect both wiring slip-connectors from the bake element. Set multimeter to lowest Ohms scale (200Ω) and measure resistance across the two element terminals.
Expected Standard: Between 15 and 25 ohms for electric bake elements. (If testing a gas range glow-bar igniter, measure current draw during ignition; expected is 3.2 to 3.6 Amps). An 'OL' reading indicates an open, burned-out element.
If Failed / Out of Spec:

Element internal coil is open or broken. Replace OEM Hidden Bake Heating Element (part #MEE61841401) or Gas Glow-Bar Igniter (part #MEG61867501).

If Passed:

Bake element resistance is perfect (18–22Ω). Proceed to Step 3.

Step 3: Physical & Electrical InspectionMultimeter & Visual
Action: Inspect the Oven Temperature Sensor Probe (RTD sensor) protruding into the upper rear corner of the oven cavity.
Bench Test: Locate the 2-pin quick-disconnect harness behind the rear panel. Measure resistance across the sensor harness pins at room temperature (77°F / 25°C).
Expected Standard: Approximately 1,080 to 1,090 ohms (1.08kΩ) at 77°F, scaling upward smoothly at approximately 2 ohms per degree Fahrenheit.
If Failed / Out of Spec:

Sensor probe is defective, out of calibration, or open. Replace Oven Temperature Sensor Probe RTD (EBG61305801).

If Passed:

Sensor probe reads within factory resistance curve. Proceed to Step 4.

Step 4: Physical & Electrical InspectionMultimeter & Visual
Action: Inspect the high-limit thermal safety thermostat switch mounted on the exterior rear cavity wall.
Bench Test: Disconnect leads and test for electrical continuity across both terminals with multimeter set to ohms.
Expected Standard: 0.0 ohms (closed continuous circuit). If tripped or burned open ('OL'), current is interrupted to the heating elements.
If Failed / Out of Spec:

Replace High-Limit Safety Thermostat Switch (6931EL3003D) and inspect oven rear cooling fan operation.

If Passed:

Safety switch closed continuous. Proceed to Step 5.

Step 5: Physical & Electrical InspectionMultimeter & Visual
Action: Test heating element relay outputs on the Main Electronic Oven Control Board (PCB).
Bench Test: Reconnect wiring, restore power, set oven to Bake at 350°F, and safely measure switched voltage output across the bake relay terminals on the main PCB.
Expected Standard: Relay clicks closed and outputs full 240V AC to the element circuit.
If Failed / Out of Spec:

Bake relay contact points are pitted, charred, or failed open on the circuit board. Replace Main Electronic Oven Control Board PCB (EBR82260601).

If Passed:

Control board delivers proper switched voltage; verify broil element (13–18Ω) and convection heating loop.

Verified OEM Replacement Parts

Cross-referenced factory part numbers for LG oven-range error code F9. Always replace defective components with authentic OEM parts to maintain UL safety certification.

Component NameOEM Part NumberManufacturerStatus
Hidden Bake Heating ElementMEE61841401LGDirect Fit OEM
Oven Temperature Sensor Probe (RTD)EBG61305801LGDirect Fit OEM
High-Limit Safety Thermostat Switch6931EL3003DLGDirect Fit OEM
Flat Gas Oven Glow-Bar IgniterMEG61867501LGDirect Fit OEM
Main Electronic Oven Control Board PCBEBR82260601LGDirect Fit OEM

Estimated Repair Cost Ranges: LG F9

Repair costs for LG oven-ranges displaying error code F9 vary based on component damage, accessibility, and whether you self-install or dispatch a local factory-trained technician.

DIY Replacement Part

$140 – $340

Direct OEM replacement part cost (excluding tools, shipping, or diagnostic meter equipment).

Pro Diagnostic Fee

$89 – $149

Standard in-home diagnostic evaluation fee by an independent technician (typically applied toward repair).

Total Pro Repair Range

$320 – $590

Typical total job cost including in-home diagnostic, authentic OEM parts, and professional labor (60–120 mins).

Pricing & Diagnostic Disclosure:

The pricing figures provided above represent broad industry averages based on nationwide market surveys and component replacement requirements. Pricing depends on multiple factors including the specific appliance brand, age, mechanical condition, diagnostic complexity, accessibility, and local labor rates. All independent repair contractors set their own independent rates and fee structures. An in-home diagnostic evaluation by an authorized technician is required to provide an exact written quote prior to any repair work.

Related Symptom Triage Guides for LG oven-ranges

If your appliance displays code F9 alongside physical operational symptoms, consult our dedicated failure triage flowcharts:

Symptom Triage

Why Does My Gas Oven Igniter Glow Orange but the Burner Won't Ignite?

View Triage Flowchart →
Symptom Triage

Why Does My Oven or Range Smell Like Gas? Emergency Safety Guide

View Triage Flowchart →
Symptom Triage

Why Is My Electric Stove Radiant Burner Not Working?

View Triage Flowchart →
Symptom Triage

Why Is My Gas Stove Burner Clicking and Won't Light?

View Triage Flowchart →
Engineering Service Hub

Looking for Full Oven & Range Repair Procedures?

Explore comprehensive diagnostic mechanics, component resistance curves, and EPA guidelines for LG units.

Oven & Range Repair Specs →
Local In-Home Diagnostic Dispatch

Tired of Troubleshooting Code F9? Get a Local LG Technician.

If multimeter bench tests confirm component failure or you prefer a professional to safely service your high-voltage LG oven-range, connect with an independent certified specialist in Colorado, Kansas, or New Mexico today.

(945) 206-7476 Urgent: (855) 796-2411Mon-Sun 7am–9pm • Fast Local Dispatch
Local In-Home Service DispatchSame-Day Available

Need In-Home Diagnostic Dispatch for Code F9?

If multimeter testing confirms an internal short, failed heating element, locked motor, or burnt control board on your LG oven-range, connect with an independent certified technician in your city.

oven & range repair in Olathe, KS
Olathe, KS Dispatch Hub
→
oven & range repair in Overland Park, KS
Overland Park, KS Dispatch Hub
→
oven & range repair in Wichita, KS
Wichita, KS Dispatch Hub
→
oven & range repair in Lawrence, KS
Lawrence, KS Dispatch Hub
→
oven & range repair in Topeka, KS
Topeka, KS Dispatch Hub
→
oven & range repair in Kansas City, KS
Kansas City, KS Dispatch Hub
→
oven & range repair in Denver, CO
Denver, CO Dispatch Hub
→
oven & range repair in Colorado Springs, CO
Colorado Springs, CO Dispatch Hub
→
oven & range repair in Aurora, CO
Aurora, CO Dispatch Hub
→
oven & range repair in Fort Collins, CO
Fort Collins, CO Dispatch Hub
→
oven & range repair in Lakewood, CO
Lakewood, CO Dispatch Hub
→
oven & range repair in Boulder, CO
Boulder, CO Dispatch Hub
→
oven & range repair in Albuquerque, NM
Albuquerque, NM Dispatch Hub
→
oven & range repair in Las Cruces, NM
Las Cruces, NM Dispatch Hub
→
oven & range repair in Rio Rancho, NM
Rio Rancho, NM Dispatch Hub
→
Serving over 120+ cities across Colorado, Kansas, and New Mexico. View all municipal service areas →
Dispatch: (945) 206-7476 Urgent Scenario: (855) 796-2411

Frequently Asked Questions: LG F9

What causes LG oven-range error code F9?

The main electronic oven control board detects that the oven cavity temperature failed to rise above 150°F (65°C) within 5 to 7 minutes after initiating a Bake, Broil, or Convection cycle.

Can I reset the F9 code by unplugging the oven-range?

While disconnecting power for 5 minutes may temporarily clear the display control memory, the F9 code will reoccur once the microcontroller detects the mechanical or electrical fault again.

What OEM replacement parts are required for LG F9?

Common OEM replacement components include: Hidden Bake Heating Element (OEM #MEE61841401), Oven Temperature Sensor Probe (RTD) (OEM #EBG61305801), High-Limit Safety Thermostat Switch (OEM #6931EL3003D), Flat Gas Oven Glow-Bar Igniter (OEM #MEG61867501), Main Electronic Oven Control Board PCB (OEM #EBR82260601).

How much does it cost to fix LG oven-range error code F9?

Professional repair for LG oven-range error code F9 typically averages $320 – $590 in total (including an estimated diagnostic fee of $89 – $149 plus labor and authentic OEM components). Sourcing authentic replacement parts yourself costs approximately $140 – $340. Final prices depend on model specifics, local labor rates, and physical technician inspection.

Dispatch: (945) 206-7476 Urgent: (855) 796-2411