Samsung Factory Service ManualFault Code: 4C

Samsung Washer Error Code 4C / 4E: Water Supply Error / Low Flow

The electronic control module detects that water is not entering the tub or water level has not reached target threshold after 10 minutes of valve activation.

OEM Brand: SamsungAppliance: washerVerified OEM Diagnostics
Samsung washer diagnostic bench testing and technical inspection for error code 4C
Samsung WASHER Diagnostic BenchCODE: 4C
Target Appliance

washer

OEM Certified Technical Diagnostic Tree

Diagnostic Tool Required

Digital Multimeter

Measure Ohms resistance, continuity & line voltage.

Triage Complexity

Advanced Diagnostic

4 Sequential manufacturer inspection branches.

Sequential Factory Diagnostic Tree

Perform each diagnostic step in order. Disconnect electrical power and turn off utility shutoffs before inspecting wiring or internal mechanical assemblies.

Digital multimeter measuring ohms resistance and terminal pin continuity on appliance electronic control board
Bench Testing Protocol

Multimeter Resistance & Continuity Verification

Before replacing any electronic control board or mechanical sensor, disconnect power and measure terminal resistance using a calibrated digital multimeter. Verify continuity (0 ฮฉ) across safety switches and compare sensor resistance against OEM specs in the diagnostic steps below.

Step 1: Physical & Electrical InspectionMultimeter & Visual
Action: Inspect residential hot and cold water shutoff valves behind washer to ensure they are fully open.
Bench Test: Disconnect supply hoses into a bucket and test water flow rate and volume.
Expected Standard: Robust water flow of at least 3 gallons per minute at 20โ€“116 PSI.
If Failed / Out of Spec:

Fully open valves, resolve house plumbing supply issues, or replace kinked water supply hoses.

If Passed:

Proceed to Step 2.

Step 2: Physical & Electrical InspectionMultimeter & Visual
Action: Unscrew water supply hoses from washer water inlet valve connectors and remove the mesh filter screens with needle-nose pliers.
Bench Test: Examine plastic mesh screens for rust flake accumulation, sand, or mineral clogging.
Expected Standard: Mesh screens clean, porous, and unobstructed.
If Failed / Out of Spec:

Clean filter screens thoroughly under running water, scrub with soft toothbrush, and reinstall.

If Passed:

Proceed to Step 3.

Step 3: Physical & Electrical InspectionMultimeter & Visual
Action: Remove top cover of washer, disconnect wiring harness to inlet valve solenoids, and measure resistance.
Bench Test: Measure DC resistance across terminals of each solenoid coil using a multimeter set to ohms.
Expected Standard: Between 1,000 and 1,500 ohms (1.0kฮฉโ€“1.5kฮฉ) across each coil.
If Failed / Out of Spec:

Replace water inlet fill valve assembly (DC62-00057A).

If Passed:

Proceed to Step 4.

Step 4: Physical & Electrical InspectionMultimeter & Visual
Action: Inspect water level pressure sensor transducer and vinyl air tube.
Bench Test: Examine air tube for kinks, pinholes, or soap buildup; measure transducer frequency signal in diagnostic mode.
Expected Standard: Air tube completely clear and airtight; sensor baseline frequency around 26.0 kHz when tub is empty.
If Failed / Out of Spec:

Replace damaged pressure sensor tube or water level pressure sensor switch (DC96-01703A).

If Passed:

Replace main electronic control board PCB (DC92-01621B) due to failed solenoid driver circuit.

Verified OEM Replacement Parts

Cross-referenced factory part numbers for Samsung washer error code 4C. Always replace defective components with authentic OEM parts to maintain UL safety certification.

Component NameOEM Part NumberManufacturerStatus
Water Inlet Fill ValveDC62-00057ASamsungDirect Fit OEM
Water Level Pressure Sensor SwitchDC96-01703ASamsungDirect Fit OEM
Main Electronic Control Board PCBDC92-01621BSamsungDirect Fit OEM

Estimated Repair Cost Ranges: Samsung 4C

Repair costs for Samsung washers displaying error code 4C vary based on component damage, accessibility, and whether you self-install or dispatch a local factory-trained technician.

DIY Replacement Part

$140 โ€“ $340

Direct OEM replacement part cost (excluding tools, shipping, or diagnostic meter equipment).

Pro Diagnostic Fee

$89 โ€“ $149

Standard in-home diagnostic evaluation fee by an independent technician (typically applied toward repair).

Total Pro Repair Range

$320 โ€“ $590

Typical total job cost including in-home diagnostic, authentic OEM parts, and professional labor (60โ€“120 mins).

Pricing & Diagnostic Disclosure:

The pricing figures provided above represent broad industry averages based on nationwide market surveys and component replacement requirements. Pricing depends on multiple factors including the specific appliance brand, age, mechanical condition, diagnostic complexity, accessibility, and local labor rates. All independent repair contractors set their own independent rates and fee structures. An in-home diagnostic evaluation by an authorized technician is required to provide an exact written quote prior to any repair work.

Related Symptom Triage Guides for Samsung washers

If your appliance displays code 4C alongside physical operational symptoms, consult our dedicated failure triage flowcharts:

Symptom Triage

Why Are Clothes Still Soaking Wet After the Washer Spin Cycle?

View Triage Flowchart โ†’
Symptom Triage

Why Does My Washing Machine Smell Like Mildew or Rotten Eggs?

View Triage Flowchart โ†’
Symptom Triage

Why Is My Front Load Washer Door Locked and Won't Open? Diagnostics

View Triage Flowchart โ†’
Symptom Triage

Why Is My Washing Machine Leaking Water? Diagnostic Guide

View Triage Flowchart โ†’
Engineering Service Hub

Looking for Full Washing Machine Repair Procedures?

Explore comprehensive diagnostic mechanics, component resistance curves, and EPA guidelines for Samsung units.

Washing Machine Repair Specs โ†’
Local In-Home Diagnostic Dispatch

Tired of Troubleshooting Code 4C? Get a Local Samsung Technician.

If multimeter bench tests confirm component failure or you prefer a professional to safely service your high-voltage Samsung washer, connect with an independent certified specialist in Colorado, Kansas, or New Mexico today.

(945) 206-7476 Urgent: (855) 796-2411Mon-Sun 7amโ€“9pm โ€ข Fast Local Dispatch
Local In-Home Service DispatchSame-Day Available

Need In-Home Diagnostic Dispatch for Code 4C?

If multimeter testing confirms an internal short, failed heating element, locked motor, or burnt control board on your Samsung washer, connect with an independent certified technician in your city.

washing machine repair in Olathe, KS
Olathe, KS Dispatch Hub
โ†’
washing machine repair in Overland Park, KS
Overland Park, KS Dispatch Hub
โ†’
washing machine repair in Wichita, KS
Wichita, KS Dispatch Hub
โ†’
washing machine repair in Lawrence, KS
Lawrence, KS Dispatch Hub
โ†’
washing machine repair in Topeka, KS
Topeka, KS Dispatch Hub
โ†’
washing machine repair in Kansas City, KS
Kansas City, KS Dispatch Hub
โ†’
washing machine repair in Denver, CO
Denver, CO Dispatch Hub
โ†’
washing machine repair in Colorado Springs, CO
Colorado Springs, CO Dispatch Hub
โ†’
washing machine repair in Aurora, CO
Aurora, CO Dispatch Hub
โ†’
washing machine repair in Fort Collins, CO
Fort Collins, CO Dispatch Hub
โ†’
washing machine repair in Lakewood, CO
Lakewood, CO Dispatch Hub
โ†’
washing machine repair in Boulder, CO
Boulder, CO Dispatch Hub
โ†’
washing machine repair in Albuquerque, NM
Albuquerque, NM Dispatch Hub
โ†’
washing machine repair in Las Cruces, NM
Las Cruces, NM Dispatch Hub
โ†’
washing machine repair in Rio Rancho, NM
Rio Rancho, NM Dispatch Hub
โ†’
Serving over 120+ cities across Colorado, Kansas, and New Mexico. View all municipal service areas โ†’
Dispatch: (945) 206-7476 Urgent Scenario: (855) 796-2411

Frequently Asked Questions: Samsung 4C

What causes Samsung washer error code 4C?

The electronic control module detects that water is not entering the tub or water level has not reached target threshold after 10 minutes of valve activation.

Can I reset the 4C code by unplugging the washer?

While disconnecting power for 5 minutes may temporarily clear the display control memory, the 4C code will reoccur once the microcontroller detects the mechanical or electrical fault again.

What OEM replacement parts are required for Samsung 4C?

Common OEM replacement components include: Water Inlet Fill Valve (OEM #DC62-00057A), Water Level Pressure Sensor Switch (OEM #DC96-01703A), Main Electronic Control Board PCB (OEM #DC92-01621B).

How much does it cost to fix Samsung washer error code 4C?

Professional repair for Samsung washer error code 4C typically averages $320 โ€“ $590 in total (including an estimated diagnostic fee of $89 โ€“ $149 plus labor and authentic OEM components). Sourcing authentic replacement parts yourself costs approximately $140 โ€“ $340. Final prices depend on model specifics, local labor rates, and physical technician inspection.

Dispatch: (945) 206-7476 Urgent: (855) 796-2411