Whirlpool Factory Service ManualFault Code: E01

Whirlpool Refrigerator Error Code E01: Refrigerator Sensor (Thermistor) Failure

The main electronic control board is unable to read temperature resistance from the fresh food compartment thermistor due to an open circuit, short to ground, or sensor drift.

OEM Brand: WhirlpoolAppliance: refrigeratorVerified OEM Diagnostics
Whirlpool refrigerator diagnostic bench testing and technical inspection for error code E01
Whirlpool REFRIGERATOR Diagnostic BenchCODE: E01
Target Appliance

refrigerator

OEM Certified Technical Diagnostic Tree

Diagnostic Tool Required

Digital Multimeter

Measure Ohms resistance, continuity & line voltage.

Triage Complexity

Advanced Diagnostic

4 Sequential manufacturer inspection branches.

Sequential Factory Diagnostic Tree

Perform each diagnostic step in order. Disconnect electrical power and turn off utility shutoffs before inspecting wiring or internal mechanical assemblies.

Digital multimeter measuring ohms resistance and terminal pin continuity on appliance electronic control board
Bench Testing Protocol

Multimeter Resistance & Continuity Verification

Before replacing any electronic control board or mechanical sensor, disconnect power and measure terminal resistance using a calibrated digital multimeter. Verify continuity (0 Ω) across safety switches and compare sensor resistance against OEM specs in the diagnostic steps below.

Step 1: Physical & Electrical InspectionMultimeter & Visual
Action: Unplug the refrigerator, remove the fresh food light lens and air tower cover to access the cabinet thermistor.
Bench Test: Measure thermistor resistance across sensor wire leads submerged in ice water (32°F / 0°C) or at room ambient (77°F).
Expected Standard: Approximately 8,700 ohms at 32°F (0°C) or 2,700 ohms at 77°F (25°C).
If Failed / Out of Spec:

Replace fresh food thermistor temperature sensor (WPW10383615).

If Passed:

Proceed to Step 2.

Step 2: Physical & Electrical InspectionMultimeter & Visual
Action: Trace wire harness from the fresh food thermistor connector back to the main control board located on the rear cabinet.
Bench Test: Measure end-to-end harness continuity and check pins for loose crimps or moisture corrosion.
Expected Standard: 0 ohms resistance across all sensor harness conductors.
If Failed / Out of Spec:

Repair harness splice or replace damaged cabinet wire harness.

If Passed:

Proceed to Step 3.

Step 3: Physical & Electrical InspectionMultimeter & Visual
Action: Inspect motorized air damper assembly between freezer and fresh food compartment.
Bench Test: Activate Service Test Mode (Step 3: Damper Test) to verify damper baffle door opens and closes mechanically.
Expected Standard: Smooth damper motor movement without gear grinding or ice binding.
If Failed / Out of Spec:

Replace motorized air damper assembly (WPW10196395).

If Passed:

Proceed to Step 4.

Step 4: Physical & Electrical InspectionMultimeter & Visual
Action: Check DC voltage supplied from main electronic control board to thermistor circuit.
Bench Test: Measure DC voltage across thermistor connector pins with unit powered in diagnostic mode.
Expected Standard: Constant 5.0V DC regulated reference voltage.
If Failed / Out of Spec:

Replace main electronic control board (WPW10312695).

If Passed:

Recalibrate temperature settings and verify cooling cycle stabilization over 24 hours.

Verified OEM Replacement Parts

Cross-referenced factory part numbers for Whirlpool refrigerator error code E01. Always replace defective components with authentic OEM parts to maintain UL safety certification.

Component NameOEM Part NumberManufacturerStatus
Refrigerator Temperature ThermistorWPW10383615WhirlpoolDirect Fit OEM
Motorized Air Damper ControlWPW10196395WhirlpoolDirect Fit OEM
Main Electronic Control BoardWPW10312695WhirlpoolDirect Fit OEM

Estimated Repair Cost Ranges: Whirlpool E01

Repair costs for Whirlpool refrigerators displaying error code E01 vary based on component damage, accessibility, and whether you self-install or dispatch a local factory-trained technician.

DIY Replacement Part

$140 – $340

Direct OEM replacement part cost (excluding tools, shipping, or diagnostic meter equipment).

Pro Diagnostic Fee

$89 – $149

Standard in-home diagnostic evaluation fee by an independent technician (typically applied toward repair).

Total Pro Repair Range

$320 – $590

Typical total job cost including in-home diagnostic, authentic OEM parts, and professional labor (60–120 mins).

Pricing & Diagnostic Disclosure:

The pricing figures provided above represent broad industry averages based on nationwide market surveys and component replacement requirements. Pricing depends on multiple factors including the specific appliance brand, age, mechanical condition, diagnostic complexity, accessibility, and local labor rates. All independent repair contractors set their own independent rates and fee structures. An in-home diagnostic evaluation by an authorized technician is required to provide an exact written quote prior to any repair work.

Related Symptom Triage Guides for Whirlpool refrigerators

If your appliance displays code E01 alongside physical operational symptoms, consult our dedicated failure triage flowcharts:

Symptom Triage

Why Is My Ice Maker Clicking but Not Dumping Ice? Diagnostics

View Triage Flowchart →
Symptom Triage

Why Is My Ice Maker Not Making Ice? Troubleshooting Guide

View Triage Flowchart →
Symptom Triage

Why Is My Refrigerator Freezing Food in the Fresh Food Section?

View Triage Flowchart →
Symptom Triage

Why Is My Refrigerator Leaking Water? Diagnostic Guide & Causes

View Triage Flowchart →
Engineering Service Hub

Looking for Full Refrigerator Repair Procedures?

Explore comprehensive diagnostic mechanics, component resistance curves, and EPA guidelines for Whirlpool units.

Refrigerator Repair Specs →
Local In-Home Diagnostic Dispatch

Tired of Troubleshooting Code E01? Get a Local Whirlpool Technician.

If multimeter bench tests confirm component failure or you prefer a professional to safely service your high-voltage Whirlpool refrigerator, connect with an independent certified specialist in Colorado, Kansas, or New Mexico today.

(945) 206-7476 Urgent: (855) 796-2411Mon-Sun 7am–9pm • Fast Local Dispatch
Local In-Home Service DispatchSame-Day Available

Need In-Home Diagnostic Dispatch for Code E01?

If multimeter testing confirms an internal short, failed heating element, locked motor, or burnt control board on your Whirlpool refrigerator, connect with an independent certified technician in your city.

refrigerator repair in Olathe, KS
Olathe, KS Dispatch Hub
→
refrigerator repair in Overland Park, KS
Overland Park, KS Dispatch Hub
→
refrigerator repair in Wichita, KS
Wichita, KS Dispatch Hub
→
refrigerator repair in Lawrence, KS
Lawrence, KS Dispatch Hub
→
refrigerator repair in Topeka, KS
Topeka, KS Dispatch Hub
→
refrigerator repair in Kansas City, KS
Kansas City, KS Dispatch Hub
→
refrigerator repair in Denver, CO
Denver, CO Dispatch Hub
→
refrigerator repair in Colorado Springs, CO
Colorado Springs, CO Dispatch Hub
→
refrigerator repair in Aurora, CO
Aurora, CO Dispatch Hub
→
refrigerator repair in Fort Collins, CO
Fort Collins, CO Dispatch Hub
→
refrigerator repair in Lakewood, CO
Lakewood, CO Dispatch Hub
→
refrigerator repair in Boulder, CO
Boulder, CO Dispatch Hub
→
refrigerator repair in Albuquerque, NM
Albuquerque, NM Dispatch Hub
→
refrigerator repair in Las Cruces, NM
Las Cruces, NM Dispatch Hub
→
refrigerator repair in Rio Rancho, NM
Rio Rancho, NM Dispatch Hub
→
Serving over 120+ cities across Colorado, Kansas, and New Mexico. View all municipal service areas →
Dispatch: (945) 206-7476 Urgent Scenario: (855) 796-2411

Frequently Asked Questions: Whirlpool E01

What causes Whirlpool refrigerator error code E01?

The main electronic control board is unable to read temperature resistance from the fresh food compartment thermistor due to an open circuit, short to ground, or sensor drift.

Can I reset the E01 code by unplugging the refrigerator?

While disconnecting power for 5 minutes may temporarily clear the display control memory, the E01 code will reoccur once the microcontroller detects the mechanical or electrical fault again.

What OEM replacement parts are required for Whirlpool E01?

Common OEM replacement components include: Refrigerator Temperature Thermistor (OEM #WPW10383615), Motorized Air Damper Control (OEM #WPW10196395), Main Electronic Control Board (OEM #WPW10312695).

How much does it cost to fix Whirlpool refrigerator error code E01?

Professional repair for Whirlpool refrigerator error code E01 typically averages $320 – $590 in total (including an estimated diagnostic fee of $89 – $149 plus labor and authentic OEM components). Sourcing authentic replacement parts yourself costs approximately $140 – $340. Final prices depend on model specifics, local labor rates, and physical technician inspection.

Dispatch: (945) 206-7476 Urgent: (855) 796-2411